EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

E23JWE-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E23JWE-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	VBAT*	CPU*
1789190836	3.79 V	30.79 °C
1789190236	3.79 V	29.79 °C
1789189852	3.78 V	29.79 °C
1789189252	3.78 V	30.79 °C
1789188655	3.78 V	30.79 °C
1789188052	3.78 V	31.79 °C
1789187452	3.8 V	32.79 °C
1789186852	3.8 V	32.79 °C
1789186252	3.8 V	32.79 °C
1789185652	3.8 V	32.79 °C
1789185052	3.8 V	34.79 °C
1789184452	3.8 V	37.79 °C
1789183852	3.81 V	39.79 °C
1789183252	3.82 V	36.79 °C
1789182652	3.81 V	33.79 °C
1789182051	3.8 V	31.79 °C
1789181452	3.79 V	32.79 °C
1789180851	3.8 V	33.79 °C
1789180251	3.78 V	36.79 °C
1789179651	3.78 V	34.79 °C
1789179051	3.79 V	35.79 °C
1789178451	3.8 V	34.79 °C
1789177851	3.78 V	36.79 °C
1789177251	3.8 V	37.79 °C
1789176674	3.8 V	35.79 °C

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

CPU: 0, 0.01, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)