EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	VBAT*	IBAT*	SOLAR*
1789233434	13.23 V	47 mA	23.59 V
1789231634	13.24 V	62 mA	23.59 V
1789229834	13.25 V	48 mA	23.59 V
1789228034	13.27 V	51 mA	23.59 V
1789226234	13.28 V	50 mA	23.59 V
1789224434	13.31 V	48 mA	23.59 V
1789222634	13.33 V	54 mA	23.59 V
1789219034	13.41 V	45 mA	23.59 V
1789217234	13.45 V	49 mA	23.59 V
1789215434	13.5 V	50 mA	23.59 V
1789213634	13.57 V	51 mA	23.59 V
1789211834	13.66 V	54 mA	23.59 V
1789210034	13.77 V	14 mA	23.59 V
1789208234	13.84 V	45 mA	23.59 V
1789206434	13.85 V	-50 mA	23.59 V
1789204634	13.85 V	44 mA	23.59 V
1789202834	13.77 V	45 mA	23.59 V
1789201034	13.93 V	-110 mA	23.59 V
1789199929	13.79 V	50 mA	23.59 V
1789198130	14.03 V	45 mA	23.59 V
1789196329	13.85 V	47 mA	23.59 V
1789194529	13.77 V	43 mA	23.59 V
1789192729	13.97 V	48 mA	23.59 V
1789192042	13.76 V	44 mA	23.59 V
1789190242	13.94 V	60 mA	23.59 V

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)