This is the latest recevied telemetry packets stored in our database for station/object EA5SW-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1779034311 | 0 Count | 276 Count | 0 Count | 0 VDC | 0 VDC |
| 1779031671 | 0 Count | 156 Count | 0 Count | 0 VDC | 0 VDC |
| 1779030505 | 0 Count | 156 Count | 0 Count | 0 VDC | 0 VDC |
| 1779027865 | 0 Count | 1014 Count | 0 Count | 0 VDC | 0 VDC |
| 1779025225 | 0 Count | 893 Count | 0 Count | 0 VDC | 0 VDC |
| 1779022585 | 0 Count | 800 Count | 0 Count | 0 VDC | 0 VDC |
| 1779019945 | 0 Count | 706 Count | 0 Count | 0 VDC | 0 VDC |
| 1779017305 | 0 Count | 602 Count | 0 Count | 0 VDC | 0 VDC |
| 1779014665 | 0 Count | 457 Count | 0 Count | 0 VDC | 0 VDC |
| 1779012025 | 0 Count | 316 Count | 0 Count | 0 VDC | 0 VDC |
| 1779011539 | 0 Count | 289 Count | 0 Count | 0 VDC | 0 VDC |
| 1779008899 | 0 Count | 185 Count | 0 Count | 0 VDC | 0 VDC |
| 1779006259 | 0 Count | 1010 Count | 0 Count | 0 VDC | 0 VDC |
| 1779003619 | 0 Count | 860 Count | 0 Count | 0 VDC | 0 VDC |
| 1779000979 | 0 Count | 693 Count | 0 Count | 0 VDC | 0 VDC |
| 1778998339 | 0 Count | 525 Count | 0 Count | 0 VDC | 0 VDC |
| 1778995699 | 0 Count | 413 Count | 0 Count | 0 VDC | 0 VDC |
| 1778993059 | 0 Count | 271 Count | 0 Count | 0 VDC | 0 VDC |
| 1778990419 | 0 Count | 185 Count | 0 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)