EA2RCF LoRa APRS MAP

My position About Powered by EA2RCF Radioclub Foronda ☰

reset

DF3EI-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DF3EI-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	B Volt*	AC V*
1745063680	5029.8 mV	3000 mV
1745063614	5029.8 mV	3000 mV
1745063440	5024.7 mV	3000 mV
1745063367	5019.6 mV	3000 mV
1745063347	5019.6 mV	3000 mV
1745063284	5014.5 mV	3000 mV
1745063239	5014.5 mV	3000 mV
1745063224	5014.5 mV	3000 mV
1745063179	5014.5 mV	3000 mV
1745063149	5009.4 mV	3000 mV
1745063134	5009.4 mV	3000 mV
1745063119	5009.4 mV	3000 mV
1745063089	5004.3 mV	3000 mV
1745063074	5004.3 mV	3000 mV
1745063059	5004.3 mV	3000 mV
1745063044	5004.3 mV	3000 mV
1745063009	5004.3 mV	3000 mV
1745062949	5004.3 mV	3000 mV
1745062601	4989 mV	3000 mV
1745062500	4989 mV	3000 mV
1745062416	4983.9 mV	3000 mV
1745062401	4983.9 mV	3000 mV
1745062381	4983.9 mV	3000 mV
1745062164	4973.7 mV	3000 mV
1745062112	4973.7 mV	3000 mV

*Used Equation Coefficients:

B Volt: 0, 5.1, 3000

B In: 0, 10, 0

B Out: 0, 10, 0

AC V: 0, 28, 3000

AC C: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)