EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

F1ZDB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1ZDB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Batt*	RX*	Relay*	Drop*
1789070310	4.3 VDC	33 pkt	12 pkt	21 pkt
1789069410	4.3 VDC	30 pkt	13 pkt	17 pkt
1789068509	4.29 VDC	33 pkt	16 pkt	17 pkt
1789067609	4.3 VDC	44 pkt	19 pkt	25 pkt
1789066709	4.29 VDC	34 pkt	13 pkt	21 pkt
1789065809	4.3 VDC	33 pkt	12 pkt	21 pkt
1789064909	4.29 VDC	32 pkt	13 pkt	19 pkt
1789064008	4.29 VDC	35 pkt	14 pkt	21 pkt
1789063108	4.29 VDC	34 pkt	13 pkt	21 pkt
1789062208	4.29 VDC	32 pkt	15 pkt	17 pkt
1789061308	4.29 VDC	36 pkt	15 pkt	21 pkt
1789060408	4.29 VDC	35 pkt	19 pkt	16 pkt
1789059507	4.29 VDC	41 pkt	14 pkt	27 pkt
1789058607	4.31 VDC	27 pkt	11 pkt	16 pkt
1789057707	4.29 VDC	35 pkt	17 pkt	18 pkt
1789056807	4.29 VDC	33 pkt	15 pkt	18 pkt
1789055906	4.3 VDC	36 pkt	15 pkt	21 pkt
1789055006	4.29 VDC	27 pkt	13 pkt	14 pkt
1789054106	4.29 VDC	30 pkt	12 pkt	18 pkt
1789053206	4.3 VDC	34 pkt	12 pkt	22 pkt
1789052306	4.29 VDC	46 pkt	18 pkt	28 pkt
1789051404	4.28 VDC	0 pkt	0 pkt	0 pkt
1789050510	4.3 VDC	34 pkt	12 pkt	22 pkt
1789049610	4.3 VDC	31 pkt	12 pkt	19 pkt
1789048710	4.29 VDC	36 pkt	17 pkt	19 pkt

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

RX: 0, 1, 0

Relay: 0, 1, 0

Drop: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)