This is the latest recevied telemetry packets stored in our database for station/object F6DEV-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | RX_rate* | RelRate* | DrpRate* | Value5* |
|---|---|---|---|---|---|
| 1793028496 | 4.24 VDC | 77 pkt/h | 3 pkt/h | 74 pkt/h | 0 |
| 1793021274 | 4.24 VDC | 96 pkt/h | 10 pkt/h | 86 pkt/h | 0 |
| 1793017678 | 4.23 VDC | 113 pkt/h | 21 pkt/h | 92 pkt/h | 0 |
| 1793014075 | 4.23 VDC | 86 pkt/h | 6 pkt/h | 80 pkt/h | 0 |
| 1793010479 | 4.24 VDC | 75 pkt/h | 3 pkt/h | 72 pkt/h | 0 |
| 1793006873 | 4.23 VDC | 58 pkt/h | 1 pkt/h | 57 pkt/h | 0 |
| 1793003262 | 4.23 VDC | 38 pkt/h | 2 pkt/h | 36 pkt/h | 0 |
| 1792999640 | 4.23 VDC | 45 pkt/h | 5 pkt/h | 40 pkt/h | 0 |
| 1792996040 | 4.24 VDC | 44 pkt/h | 6 pkt/h | 38 pkt/h | 0 |
| 1792992440 | 4.23 VDC | 39 pkt/h | 4 pkt/h | 35 pkt/h | 0 |
| 1792988840 | 4.23 VDC | 28 pkt/h | 2 pkt/h | 26 pkt/h | 0 |
| 1792985239 | 4.24 VDC | 36 pkt/h | 3 pkt/h | 33 pkt/h | 0 |
| 1792981644 | 4.24 VDC | 25 pkt/h | 2 pkt/h | 23 pkt/h | 0 |
| 1792978020 | 4.23 VDC | 28 pkt/h | 2 pkt/h | 26 pkt/h | 0 |
| 1792974419 | 4.24 VDC | 26 pkt/h | 2 pkt/h | 24 pkt/h | 0 |
| 1792970819 | 4.23 VDC | 26 pkt/h | 4 pkt/h | 22 pkt/h | 0 |
| 1792967219 | 4.23 VDC | 34 pkt/h | 3 pkt/h | 31 pkt/h | 0 |
| 1792963619 | 4.23 VDC | 40 pkt/h | 5 pkt/h | 35 pkt/h | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
RX_rate: 0, 1, 0
RelRate: 0, 1, 0
DrpRate: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)