EA2RCF LoRa APRS MAP Backup

My position About Go to MAIN map Powered by EA2RCF Radioclub Foronda ☰

reset

DO6GZ-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO6GZ-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Satellite*	Battery*	Temperatu*
1790366284	9 V	0.01 V	50 °C
1790366152	8 V	0.01 V	49 °C
1790366032	8 V	0.01 V	49 °C
1790365910	9 V	0.01 V	49 °C
1790365790	7 V	0.01 V	49 °C
1790365668	9 V	0.01 V	49 °C
1790365548	7 V	0.01 V	49 °C
1790365428	9 V	0.01 V	49 °C
1790365306	9 V	0.01 V	49 °C
1790365186	8 V	0.01 V	49 °C
1790365064	10 V	0.01 V	49 °C
1790364944	9 V	0.01 V	49 °C
1790364824	10 V	0.01 V	49 °C
1790364702	7 V	0.01 V	49 °C
1790364582	9 V	0.01 V	49 °C
1790364460	10 V	0.01 V	48 °C
1790364340	9 V	0.01 V	49 °C
1790364221	8 V	0.01 V	49 °C
1790364098	9 V	0.01 V	49 °C
1790363978	8 V	0.01 V	49 °C
1790363857	8 V	0.01 V	49 °C
1790363737	8 V	0.01 V	49 °C
1790363617	8 V	0.01 V	49 °C
1790363494	11 V	0.01 V	49 °C
1790363375	10 V	0.01 V	49 °C

*Used Equation Coefficients:

Satellite: 0, 1, 0

Battery: 0, 0.01, 0.01

Temperatu: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)